Instalar Placa de Rede no Linux FEDORA LIVECD

paulosix12
(usa Slackware)

Enviado em 09/01/2013 - 14:13h

Bom Dia...
Estou iniciando no linux..ontem resolvi trocar de distro e instalar a FEDORA....Só que infelizmente minha placa on-board esta queimada e estou utilizando uma placa PCI...Gostaria de saber como configura-la ??

*Obs Tive o mesmo problema com ubuntu..Na época achei um tutorial de como conectar sem Utilizar "gerenciador de redes" Do linux....Apenas configurar um Documento de texto..

Obrigado Pela atenção !!

Ifconfig -a

[liveuser@localhost ~]$ su
\[root@localhost liveuser]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::205:ff:fea0:187 prefixlen 64 scopeid 0x20<link>
ether 00:05:00:a0:01:87 txqueuelen 1000 (Ethernet)
RX packets 8 bytes 480 (480.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 3 bytes 258 (258.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 16 base 0xec00

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 16436
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 80 bytes 6632 (6.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 80 bytes 6632 (6.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

removido
(usa Nenhuma)

Enviado em 09/01/2013 - 15:01h

Não conheço Fedora, mas quem sabe esses comandos mostram alguma coisa que o pessoal aqui possa interpretar e te ajudar. Coloca os resultado aqui:

lspci -nn
sudo lshw -C network
nm-tool

paulosix12
(usa Slackware)

Enviado em 09/01/2013 - 15:19h

[root@localhost liveuser]# lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 4 Series Chipset DRAM Controller [8086:2e30] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation 4 Series Chipset PCI Express Root Port [8086:2e31] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01)
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01)
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01)
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01)
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01)
00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA IDE Controller [8086:27c0] (rev 01)
01:00.0 VGA compatible controller [0300]: nVidia Corporation G96 [GeForce 9500 GT] [10de:0640] (rev a1)
02:00.0 Multimedia controller [0480]: Philips Semiconductors SAA7130 Video Broadcast Decoder [1131:7130] (rev 01)
02:01.0 Ethernet controller [0200]: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY [13f0:0200] (rev 31)

sudo lshw -C network
Não funcionou !!


[root@localhost liveuser]# nm-tool
NetworkManager Tool

State: disconnected

- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: sundance
State: unavailable
Default: no
HW Address: 00:05:00:A0:01:87

Capabilities:

Wired Properties
Carrier: off

paulosix12
(usa Slackware)

Enviado em 09/01/2013 - 15:23h

A placa de rede (PCI) é esta : Descrição do dispositivo IC Plus IP100 Fast Ethernet Adapter
" Ethernet controller [0200]: Sundance Technology Inc / IC Plus Corp IC Plus IP100A Integrated 10/100 Ethernet MAC + PHY [13f0:0200] (rev 31)"
Obrigado !!